A boat lift can elevate a hefty vessel out of the water every single day in order to shield it from the onslaught of water damage, but the salty spray and excess humidity found in Southwest Florida can corrode metallic parts and electrical wiring. A professional Boat Lift service in Cape Coral, FL company like Dockside Mobile Boat and Lift Maintenance can identify the signs of early corrosion in wiring as well as diagnose engine issues when you measure the voltage under full load. And technicians ensure your setup stays strong over time.
Prevent Damage to Boat Lift Wiring from Summer Moisture
The overly humid conditions they generally have all summer long are also what the outside of the motors are exposed to for that amount of time. High humidity can increase the risk of moisture entering motor housings through damaged seals or other openings. This moisture may cause corrosion, damage electrical connections, and increase the risk of short circuits. You’ll hear that low-level hum just before it shorts out the entire boat motor all at once from the excess. But to prevent losses and those unexpected electrical short-outs, have your boat motor and all your contacts maintained and cleaned by the experts. And keeping connections clean prevents serious damage down the line.
How to Fix Slipping Belt & Drive Pulley Burnouts
Drive belts and pulleys transfer the power from your engine to the middle gear set with mechanical force. Over time, worn belts will slip constantly and make the electric motor accelerate without actually raising your boat. Heat from the wasted energy and rubber belts causes a lot more wear and tear than most of us realize, but simply tightening the belts will make your boat lift again. And the correct adjustment of the pulleys will keep your main drive unit from premature failure. But relying on professional Boat Lift service in Cape Coral, FL will keep all of your mechanisms tightly in place.
Protection of Control Box Switches from the Sea’s Elements
Controls are exposed to the elements constantly throughout the year. Rain, salt air, and sun are a constant assault on these vital components. Switch corrosion prevents electrical current from reaching the motor and therefore stops your vessel from being raised. You may have a bad directional switch where your lift will go down but not up. But bad switches are easily replaced to protect the enclosure from the elements. And Dockside Mobile Boat and Lift Maintenance tests the operation of each control circuit to deliver perfect dock operation every time.
Cradle Weight Balance Issue on Single Drive Motors – How To Fix
Unequal weights on the cradle will divide the load unequally between the two drive units, meaning one lift is overburdened and must carry the total weight by itself. The overloaded motor will draw too much current and will disconnect itself in the mode of a fail-safe device to avoid a permanent winding failure. But leveling the lifting cables balances the load evenly across the frame. And adjusting the bunks ensures proper support for every single hoist.
Overhead Security Testing of Auto Brakes Systems
The brakes secure the entire cradle in place as soon as the electric motor stops. For instance, a skipping brake suggests that the vessel may slide backward into the water at any time. Internal brake pads are worn away after a few hundred lifts, but friction plates can be readjusted to continue that tight grip, and replacement brake assemblies are installed to keep the boat even higher above the water. But Dockside Mobile Boat and Lift Maintenance tests the auto-brakes to full weight to verify safety during routine Boat Lift service in Cape Coral, FL. And regular brake inspections stop unwanted slipping dead in its tracks.
Remove the Voltage Drop Created by Long Extension Cords
Surges, such as the power surges that frequently come on when you run electric motors over extension cords without the proper wire gauge, can be one cause of constant motor problems. When a motor is running at a lower voltage, it pulls more current, creating damaging internal heat in the windings. Running an electric motor on a lower-than-specified voltage will destroy the wire insulation on the windings instantly. But dedicated electrical lines keep you charged for those bigger lifts, and voltage tests under load tell you that all systems are go. And checking lines prevents unexpected system failure.
Schedule Professional Care to Maintain Long-Term Lift Performance
Consistent dock maintenance ensures that minor mechanical issues won’t ruin your epic, long-weekend outing on the water. Preventative care will extend the life of your investment so you have hassle-free launch days all year round. Call a professional today for quality Boat Lift service in Cape Coral, FL and enjoy every single season without worry. But you can also trust expert technicians for electrical repairs to get your boat lift and dock maintenance back on track as quickly as possible. And Dockside Mobile Boat and Lift Maintenance guarantees top performance for your equipment.
FAQs
Why Won’t My Boat Lift Motor Lift The Boat?
Common causes of a humming motor include a faulty capacitor, lack of incoming voltage, or a jammed drive gear. With a faulty start capacitor, the engine will hum, as it won’t have enough torque to start rotating the drive shaft when under load.
How Often Should Boat Lift Motors Be Serviced In Cape Coral?
Boat lift systems installed in the salt air must be professionally serviced two or three times annually to ensure they remain clean of spray and resistant to the harmful salt air.
Can A Worn Drive Belt Ruin The Lift Motor?
Yes, if you see the weight never moves at all while in use then you have a loose or worn belt. If your belt slips in use, the motor end will spin rapidly and get very hot due to friction. This can burn out the motor windings and cause it to fail prematurely.
